Air cheap compressor hardware - Campbell Hausfeld FP205299AV, Makita MAC700, Makita MAC2400, Senco PC0947, Porter-Cable CPFAC2600P, DeWalt D55155, Porter Cable C3151, Makita MAC5200, Hitachi EC12, Porter-Cable C3551

Air Cheap Compressor Hardware - 1 2 3

*2 Gallon Wall-Mountable Air* Compressor \| Campbell Hausfeld FP205299AV**
	$115.00 by Campbell Hausfeld 2-gallon tank adds greater stored air capacity Up to 50% quieter than competitive models for a more comfortable work environment On-board accessory storage keeps small accessories organized and readily available Hose management system keeps hose coiled when not in use for easy transportation and compact storage Using the included hardware, the compressor can be wall-mounted freeing up valuable work space
*The Hotdog 12.4 Amp 2 Horsepower 2-1/2 Gallon Oiled Single Hotdog Compressor* \| Makita MAC700**
	$288.00 >> $176.40 by Makita 18 by 10 by 22 inches; 52 pounds; 1-year warranty 1/4-inch brass Makita universal coupler Cast-iron pump and roll cage construction 3.3 cfm delivered at 90 psi; low 1,720 rpm extends motor life and lowers noise 12.4 amp, 2-horsepower, 2-1/2-gallon oiled single hot dog compressor with handle found in MAC700's description: From the Manufacturer The new MAC700 - Hotdog compressor by Makita is blowing away the competition with built-in features such as a super quiet motor that draws only 12.0HP AIR COMPRESSOR 12. hot dog tank Low amp draw & oil lubricated Roll-bar handle Industrial air filter & cast iron cylinder Oil sight glass & lever handle ball valve Built-in thermal overload for motor protection MAC700 2HP AIR COMPRESSOR. found in MAC700's reviews: Great little compressor - Be sure to fill with oil and install the air filter before starting. It required drilling out the check valve, retapping the threads, buying an equivalent part at the hardware store, and reinstalling. Serious PITA, but cost was minimal and repair works fine. All in all, a great little compressor, and the best choice if noise is a concern.

*13 Amp 2-1/2 Horsepower 4 Gallon Oiled Twin Hot Dog Compressor* \| Makita MAC2400**
	$460.00 >> $249.00 by Makita 19-3/8 by 18 by 18-3/4 inches; 77 pounds; 1-year warranty 1/4-inch brass Makita universal coupler Cast-iron pump and roll cage construction 4.2 cfm delivered at 90 psi; low 1,720 rpm extends motor life and lowers noise 13 amp, 2-1/2-horsepower, 4-gallon oiled twin hot dog compressor with handle found in MAC2400's description: From the Manufacturer The new MAC2400 - Twin Stack air compressor by Makita is blowing away the competition.3 amps to operate, a lower 1720 RPM rating and a heavy duty Intake Air Filter system like no other, its easy to see how this unit will out last and outperform everyone else. Large automotive style industrial air filter for increased air intake and greater efficiency. found in MAC2400's reviews: It's a sweet piece - Having used various compressors in the past from cheap chinese brands to high end models this unit ranks right up there with the better ones. If this is the size compressor that suits your needs you won't go wrong buying this one. UNBELIEVABLY QUIET!!! - FIRST OF ALL THIS COMPRESSOR IS THE MOST UNBELIEVABLY QUIETEST COMPRESSOR I'VE EVER OWNED! NOT TO MENTION WE RAN 2 FRAMING NAILERS ALL DAY LONG AND IT NEVER EVEN AS MUCH AS BARKED, THE RECOVERY TIME IS SUPERB! NOW THE DOWN SIDE THIS SUCKERS HEAVY!!! IF YOU HAVE A BAD BACK GET A CHEAP NOISE MAKER AND EAR PROTECTORS OR GO WITH THE PROFFESSIONAL COMPRESSOR AND HIRE A LABORER YOU CANT BEAT THIS THING!!!!. *Superb compressor* - Makita needs to fire their packing design person. - I am extremely happy with the compressor for general garage, woodworking, and around-the-house duties. My first unit was badly damaged by a loose air filter (with a thick metal bolt) that was just floating around in the box. I returned it, second unit also damaged in exactly the same spot also by the same free-floating air compressor. Addendum - added just for laughs - I went to a local hardware** store that sells these and happened to see one on display.
*/ FP18KIT 18-Gauge Brad Nailer Compressor* Combo Kit \| Senco PC0947**
	$249.00 >> $197.00 by Senco 1-year warranty on nailer; 90-day warranty on compressor Includes nailer, 1/4-inch -by-25-foot hose, safety glasses, fittings, oil, 1,200 brad nails, wrenches, and manuals Compressor: 1 horsepower, 2-1/2 gallons; aluminum cylinder with steel sleeve; 20 pounds Nailer: adjustable depth of drive, rear exhaust, easy-open latch, no-mar pad, low-load indicator 18-gauge brad nailer and 1-gallon compressor combo kit found in PC0947's description: FinishPro 18 FEATURES Extra power — Drives fasteners up to 2" in hard wood applications Belt hook — For convenience Adjustable depth-of-drive Rear exhaust — Keeps oil and dust away from work surface Easy-open latch — For quick and comfortable loading Hardened steel driver — For extended life Full soft grip — For comfort and control Low load indicator — Visible fastener indication No-mar pad — To protect work materials One-year warranty Includes case, fitting, oil, hex wrench and fastener rebate Projects Baseboard,cabinets, casebacks, chair rail, finish and trim, furniture frames, furniture trim, mirror and picture frames, trim FinishPro 18 SPECIFICATIONS Power (in/lbs): 168 Height: 9.3 bar) Mode of Operation: Restrictive Trigger Fastener Types Gauge: 18 Fastener Range: 5/8"—2" Finish: Galvanized What's in the Box This kit comes complete with the FinishPro 18 brad nailer, a Senco 1/2 hp (1 hp peak), 1-gallon compressor, 1/4-by-25-foot coil hose, safety glasses, fittings, tool oil, variety pack of 1,200 brad nails, tool wrenches and manuals. Product Description Finish Pro 18 Combo Kit, Perfect For Woodworkers & Punch List Contractor, Kit Includes, Lightweight Oilless, 1HP Compressor, Finish Pro 18 Brad Nailer 5/8" To 2", Hose, Fittings, Sample Pack Of Brads, Safety Glasses & Bottle Of Oil. found in PC0947's reviews: This contractor is very pleased... with the compressor - I own several portable compressors, but hate to lug them around. The little compressor is lightweight and perfect for small jobs like these. On bigger jobs I still use one of my heavy duty compressors. Regarding the cheap 1/4 inch hose. Anyone with half a brain knows it's a cheap piece of krap, but will work fine for the occasional hobbiest. I'm impressed. - I upgraded to this from a cheap little electric brad nailer that could not sink a 1" brad. The compressor is small & quiet and has absolutely no problem keeping up with the nailer. I own an old 5 horse 220 v compressor but wanted something to use inside the house without running hundreds of feet of hose from the garage.
*15 Amp 2 Horsepower 6-Gallon Oil-Free Pancake Compressor* \| Porter-Cable CPFAC2600P**
	$316.16 >> $167.00 by Porter-Cable 32 pounds; 1-year warranty Includes compressor, ASME safety valve, regulator, gauges, 1/4-inch quick coupler, manual Cast-iron construction Provides 3.7 cfm at 40 psi and 2.6 cfm at 90 psi; air-regulator and quick-connect coupler 15 amp, 2-horsepower, 6-gallon oil-free pancake compressor; handle; built-in thermal overload protector found in CPFAC2600P's description: com Review This Porter-Cable 2-horsepower, 6-gallon pancake compressor transports easily but has plenty of capacity and power--enough to support heavy use of brad and finish nailers and moderate use of framing nailers. Features include a high-flow regulator, an easy-to-read air pressure gauge, automatic thermal overload protection, an industrial-style quick-connect body in the air outlet, and a long-life motor with replaceable brushes. The compressor weighs 32 pounds and has a handle built into the motor housing, so it's relatively portable. This Porter-Cable is as convenient and easy to use as any compressor out there, and it's just about ideal for brad and finish nailers that are being used inside people's homes on a regular basis. --Jonathon Tudor From the Manufacturer This oil-free 2-hp pancake-style air compressor has a new high pressure design that provides 28-percent more usable air! This allows more run time and less down time. The high-flow regulator keeps the tank pressure between 120 PSI and 150 PSI, allowing a greater reserve air capacity. Lightweight for portability, this compressor has plenty of power to fire all brad and finishing nailers as well as moderate usage of roofing and framing nailers. Includes compressor, high flow air regulator and gauges, quick coupler, and instruction manual.8 HP Running Built-in automatic thermal overload protection Larger Easy to read regulated air pressure gauge Universal, High-FloSM, push-to-connect coupler in air outlet One year warranty 150 PSI - 10 gallon equivalent tank size as compared to conventional 125 PSI model 87 Dba Oil-free pump design for durability and no maintenance Long-life motor with replaceable brushes High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch) 6 gallon tank supports heavy usage of stapler, brad and finish nailer, standard-to-heavy roofing and standard framing nailer 120 Volt, universal motor starts easily under low voltage conditions Extension cord use without tripping circuit breakers Standard Equipment: Compressor, ASME safety valve, air regulator and gauges, 1/4" quick coupler, and operating manual SPECIFICATIONS Lubrication: Oil Free Gauges: 2 Quick Couple: 1/4" NPT Weight (Lbs. PSI: 150 SCFM Air Delivery @40 PSI: 3.7 SCFM Air Delivery @90 PSI: 2. Product Description 2 HP, 6 Gallon, Oil-Free Pancake Air Compressor, 150 PSI Maximum Tank Pressure, 3.6 SCFM @ 90 PSI 87 DBA, 15 AMPS, Built-In Thermal Over Load Protection, Hi-Flo Air Regulator With Quick-Connect Coupler, Regulated Pressure Gauges, Includes ASME Safety Valve, 1 Year Warranty. found in CPFAC2600P's reviews: *Good compressor* for a good price - I've owned a large compressor for years and needed something that can easily be ported anywhere - the large one is nice, but combersome for small jobs. Originally I bought a similar cheaper competing unit from homedepot - it was cheap (=inexpensive but badly made, very noisy) and was brought back immmediately, since it was a useless toy. This small compressor is actually used a lot more than my original compressor. Spraying paint I haven't tried and probably would not work well - it just doesn't have the air delivery. That is what my large compressor is used for. It is an oil-less compressor** - so it is relatively noisy but noise means power, no? :) .
*15 Amp 2-3/4 Horsepower 4 Gallon Oiled Single Hot Dog Compressor* \| DeWalt D55155**
	$676.00 >> $365.00 by DeWalt 23 by 23 by 13-1/2 inches; 68-1/2 pounds; 1-year warranty Includes DEWALT synthetic compressor oil and pressure regulator Cylinder constructed of cast iron 4-1/2 cfm delivered at 100 psi; dual soft start valve for cold-weather starts; oil-lubricated pump 15 amp 2-3/4-horsepower 4-gallon oiled twin hot dog compressor with carrying handle found in D55155's description: com Review At just a foot high and less than two feet wide out of the carton, this compressor was quite a bit smaller than we expected, so to be fair, we quickly lowered our expectations. The joke was on us, though, because this little powerhouse just doesn’t quit, and we learned that you can’t judge a compressor by its size. Emglo’s half-century in the compressor business is evident in this model, and with a couple of small exceptions (we’ll get into that in a minute), we don’t think anyone could make a finer piece of air power. Now, this may be a plus or a minus in your book, but we liked the fact that the compressor is factory set to power on at 100 psi an+d shut off at 120 psi, and the cycle time was under 15 seconds.) It has air aplenty for two nailers at once, and with that fast recovery, the job will get done in no time. In balance, this is one of the best compressor’s we’ve seen for the size, power, ruggedness and incredible portability it offers. Here’s to a great pairing of two great toolmakers.--Kris Jensen-Van Heste Product Description DeWalt's 2-horsepower, 4-gallon compressor features an oil-lubricated design with a cast-iron cylinder to guarantee job site durability. The new roll-cage design and integrated control panel protects the compressor and the controls from accidental damage. Carrying the compressor is easy, too: the flat design lets the user tote the compressor comfortably like a suitcase. The package comes with the initial fill of DeWalt synthetic air compressor oil. From the Manufacturer This 4-gallon hand-carry compressor was designed to meet the tough demands of the job site. The handle is situated to allow the user to carry the compressor with one hand in a natural walking position. The roll cage and integrated instrument panel protect the compressor and instruments from damage. Comes with the initial fill of DeWalt's synthetic air compressor oil. Includes DeWalt synthetic compressor oil 2 universal quick couplers Regulator Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty Product Description 2 HP, 4 Gallon, Electric Single Tank Hand Carry Compressor, 4. found in D55155's reviews: A very good compressor - I replaced my hotdog style oil-less compressor* when the connecting rod decided to break.* While at the local hardware store I saw the DeWalt D55155 compressor and thought, "geez, you could not miss that compressor!" The bright yellow paint made this compressor stand out and then that's when I saw the name Emglo. This compressor also has a ball valve on the bottom of the tank for easy draining. This ball valave is also inside the frame as is every component of the compressor. It's mounted inside the roll cage near the copper line running from the compressor to the tank. It might be, but, I put the compressor away from where I'm working so this is not an issue. As with any compressor* you have to keep the extension cords short.* So, would I buy this compressor* again if I had to? You bet!.*
Job Boss 15 Amp 3.5 Horsepower 4-1/2 Gallon Oil-Free Wheeled Single Hot Dog Compr \| Porter-Cable C3151
	$534.56 by Porter Cable 85 pounds; 1-year warranty Includes compressor, mobility kit, and manual Cast-iron construction 2-port removable console for remote air regulation; full roll cage to protect kit; 150 max psi 15 amp, 3-1/2-horsepower, 4-1/2-gallon oil-free wheeled single hot dog compressor with handle found in C3151's description: com Porter-Cable’s solved the compressor mobility problem on two levels with this tool. First, and most impressively, it’s got a two-port removable console for remote air regulation and higher air pressure right where you’re working. And the compressor itself has wheels and an extension handle, making life easier on you. Let’s face it: This compressor’s big, heavy and loud, with a max psi of 150. You can run three or four guns at once off it with a splitter and have no air supply problems whatsoever.5 gallon, oil-free contractor style compressor is packed with features. The high-flow air regulator and two-port removable console are winning combinations for contractors. Having the ability to remove the console gives the user the opportunity to remote air regulation and gain higher air pressure closer to the job site. Air delivery at 40 PSI: 7. What's in the Box C3151 Job Boss Compressor, mobility kit, manual.5 gallon, oil-free contractor style compressor is packed with features. The High-flo air regulator and 2-port removable console are winning combinations for contractors. Having the ability to remove the console gives the user the opportunity to remote air regulation and gain higher air pressure closer to the job site. Product Description Includes Compressor, Mobility kit, ASME safety valve, Operating manual, Limited one-year warranty. found in C3151's reviews: Good, But..... - The only complaint is that the outlet pressure regulator is cheap.

*13.8 Amp 3 Horsepower 5 Gallon Oiled Wheeled Single Hot Dog Compressor* \| Makita MAC5200**
	$544.00 >> $319.00 by Makita 29 by 19 by 19-1/2 inches; 88 pounds; 1-year warranty 1/4-inch brass Makita universal coupler Cast-iron pump and roll cage construction 6-1/2 cfm delivered at 90 psi; low 1,720 rpm extends motor life and lowers noise 13.8 amp, 3-horsepower, 5-gallon oiled wheeled single hot dog compressor and folding handle found in MAC5200's description: com Product Review Whether you need a compressor for woodworking, painting, caulking or construction, this 5-gallon Makita is a great choice, primarily because of its impressive 6-1/2 cfm at 90 psi on a 13. Built-in Storage Compartment - Conveniently stores air fittings & accessories. Air Hose Wrap - Stores 50 of 3/8" Air Hose with handle folded or upright. Large automotive style industrial air filter for increased air intake and greater efficiency. found in MAC5200's reviews: If I had to do it again it would not be my first choice. - They used cheap* plastic wheels, I broke one the first day I used it.*
*14.5 Amp 2 Horsepower 4 Gallon Oiled Twin Hot Dog Compressor* \| Hitachi EC12**
	$417.29 >> $207.00 by Hitachi 60 pounds; 1-year warranty Includes DEWALT synthetic compressor oil and pressure regulator Cylinder constructed of cast iron 4.1 cfm delivered at 90 psi; shut-off valve at line and auto reset 14-1/2 amp 2-horsepower 4-gallon oiled twin hot dog compressor with carrying handle found in EC12's description: com Hitachi’s 2-horsepower compressor is one of the hardest-working units on the market.1 cfm of free air at 90 psi--enough to easily run two tools at once. Because of its compact size and trim weight, it’s the perfect compressor for the home do-it-yourselfer, but taking into account its power and portability, contractors will love it, too.--Kris Jensen-Van Heste From the Manufacturer This Hitachi air compressor is powered by a 2 hp, 115-volt direct-drive motor and oil lube pump at 3,450 rpm.1 cfm of free air, at 90 psi. From the Manufacturer The Hitachi EC12 air compressor is powered by a 2-horsepower, 115-volt direct-drive motor and oil lube pump at 3,450 rpm. It delivers 4 cubic feet per minute of free air at 90 psi.2 cubic feet per minute of free air Specifications Horsepower: 2 Amps: 15 Speed: 3,450 rpm Air displacement: 8. Oil lube single piston compressor type, line regulator with gauge, direct drive electric motor, suction cup feet for extra stability, O-ring on draincock makes valve easy to open and close and resists stripping, vertically stacked twin tanks. found in EC12's reviews: Zero stars for Amazon & Tool Crib - Based on the fantastic reviews, I decided to purchase this compressor. The box arrived, and when I opened it, I was a little surprised at how little packing material there was - just a box with the compressor inside. This may be a great product, but I'll buy my major hardware purchases locally, so I can return broken products. *CAUTOIN!!!! CHEAP* SAID MADE IN CHINDA - Well first when UPS droped off untied the plastic it said on unit MADE IN CHINA, Then when I lifted out of bag I saw pieces of what looked like pot metal in the bottom of bag, What happen was that someone sit it down to hard, busted the motor and compressor from the frame, Metal looked about 1/16" thick,plus free shipping took 13 days to arrive.00 to wait 13 days to get a china made busted compressor**.
Job Boss 12 Amp 2-1/2 Horsepower 4.5 Gallon Oiled Wheeled Single Hot Dog Compress \| Porter-Cable C3551
	$641.68 >> $349.99 by Porter-Cable 86 pounds; 2-year limited warranty Includes compressor, mobility kit, ASME safety valve, manual Cast-iron construction 12 amps; 150 psi, enough to operate 2 nailers at once; roll bar to protect motor and pump 2-1/2-horsepower 4-1/2-gallon oiled wheeled single hot dog compressor found in C3551's description: If you're a contractor looking for the right compressor, you've found it.--Kris Jensen-Van Heste From the Manufacturer Why lift when you can roll? The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features you’ll like. The High-flo air regulator and 2-port removable console are winning combinations for contractors looking for performance and versatility. This compressor is designed with a removable console for maximum mobility and air pressure.5 HP single tank air compressor Oil-lube air compressor for maximum durability 150-PSI tank pressure for longer tool run time, Quieter motor is easy on eardrums 120 V/ 60 hertz/1 phase motor Two pole, 3450-RPM capacitor start induction motor for maximum air delivery Includes 1-year limited warranty on parts and accessories SPECIFICATIONS 150-PSI tank 3450-RPM capacitor start induction motor 8 oz. oil capacity Product Description The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features youll like. The High-flow air regulator and 2-port removable console are winning combinations for contractors looking for performance and versatility.5 gallon, mobile, contractor-style, single tank air compressor. 2-port removable console to allow remote air regulation and higher pressure closer to the job site.5 gallon storage capacity air tank supports heavy use of brad nailers, staplers, and finish nailers; moderate use of roofing and framing nailers.5 gallon 150 PSI portable air compressor, Mobility kit, ASME safety valve, and Operator manual. found in C3551's reviews: mine came damaged too! - The main pressure gauge was sheared off (behind the control panel) and the frame was dented and air filter busted. i will sell it cheap! b update.